Consumers do not need to operate their own Water Filter Spare Parts(KOKOELECTRIC) https://www.kokoelectric.com/
. Although they are equipped with installation schematics, they are not professionals after all. If they make a mistake one step at a time,... moreConsumers do not need to operate their own Water Filter Spare Parts(KOKOELECTRIC) https://www.kokoelectric.com/
. Although they are equipped with installation schematics, they are not professionals after all. If they make a mistake one step at a time, they may make a mistake one step at a time. After all, the installation quality of household water filters directly determines the future use quality.
1. It is better not to install it in a place with direct sunlight. It is better to control its normal use temperature to between 1 degree and 39 degrees. Either in summer or winter, too high or too low a temperature may cause the water filter to freeze or generate algae.
2. Test the inlet water pressure. Before the installation of water purification products, the water pressure of the raw water in the customer's home must be tested. If the water pressure of the raw water is too small, it may lead to the risk of water pipe falling off, equipment damage and water leakage, and a pressure reducing valve need... less
Molten plastic particles are moulded into plastic injection products in the process of injection moulding. The process is still relatively complicated. Injection engineers need to pay attention to some injection process parameters to ensure the quality... moreMolten plastic particles are moulded into plastic injection products in the process of injection moulding. The process is still relatively complicated. Injection engineers need to pay attention to some injection process parameters to ensure the quality requirements of the final injection products. What process parameters should Chair Mould(FURNITUREMOULD) https://www.furnituremould.com/product/chair-table-stool-mould/
processing pay attention to?
First, the moulding cycle of chair mould injection products includes injection time and product cooling time. The effective control of these times has a profound impact on the quality of products. Before injection moulding, we should determine the moulding cycle of the product by sample pattern and other methods.
Second, the temperature of the chair mould, the crystallization temperature and speed of different plastic particles are different, and the appearance, deformation, size and rubber mould of the products have different requirements, which make the... less
The overall performance of the practical Copper Clad Aluminum Winding Wire(XINYU) http://www.xinyu-enameledwire.com/product/enameled-rectangular-copperaluminum-wire/
conductor is better than that of the pure copper conductor. The wire and cable industry... moreThe overall performance of the practical Copper Clad Aluminum Winding Wire(XINYU) http://www.xinyu-enameledwire.com/product/enameled-rectangular-copperaluminum-wire/
conductor is better than that of the pure copper conductor. The wire and cable industry adopts the copper clad aluminum winding wire, which is also a good way to alleviate the pressure of the current enterprise. Today, Xiaobian will give you a brief introduction.
The copper clad aluminum winding wire is a copper layer which is concentrically coated on the surface of the aluminum or aluminum/steel alloy core material and is drawn, and the thickness of the copper layer is above 0.55 mm. Due to the skin effect of high-frequency signal transmission on the conductor, the cable signal is transmitted on the surface of the copper layer above 0.008 mm. The inner conductor of the copper clad aluminum winding wire can fully meet the signal transmission requirements, and the transmission characteristics of the signal and the same diameter The... less
The surface of the palm oil chain(GETECHAIN) https://www.getechain.com/product/palm-oil-chain/
should be noticed. The non-standard chain manufacturer tells you that the palm oil chain sprayed and rusted surface should be primed immediately. When... moreThe surface of the palm oil chain(GETECHAIN) https://www.getechain.com/product/palm-oil-chain/
should be noticed. The non-standard chain manufacturer tells you that the palm oil chain sprayed and rusted surface should be primed immediately. When painting, it should be done in a clean place. The ambient temperature should be Above 5 °C, palm oil chain manufacturers recommend that your humidity should be below 85%, and the external temperature of the workpiece should not exceed 60 °C; if there are no special requirements for each part, one layer of primer should be applied (not including maintenance primer). , paint leakage is not allowed, the color of each layer of paint should be different, the dry film thickness of each layer of paint is 25 ~ 35 um, the total thickness of the paint dry film is not less than 75um;
The initial tension is too small. The insufficient tension of the conveyor belt away from the drum causes the conveyor belt to slip. This situation generally occurs when the plate chain... less
